Audio Ease Altiverb Plugin

Used on Lamar's vocals for "All the Stars" as stated by producer Matt Schaeffer in this May 2018 *Sound on Sound* interview. > Kendrick Lamar’s vocal audio tracks, named after his teenage stage name K.Dot, consist of his first verse rap track, ‘VS 1 LD’, and 10 tracks for three moments in the track where he sings the pre-hook in a robotic voice. The verse rap track only has the AIR Flanger on it, and is sent to the ‘Dot VS LD’ aux track, which has eight inserts and five sends. Nine of the 10 pre-hook tracks have Auto?Tune, while the top four have a number of plug-ins on the inserts, including the EQ3 seven-band, Waves RVox, UAD Galaxy Tape Echo, SoundToys Little AlterBoy, SoundToys MicroShift and Valhalla Vintage Verb. These four are sent to a ‘Hook Ref’ aux track higher up in the session with another four plug-ins on the inserts and five sends. The other six are backing vocals to the four other pre-hook tracks and have no other plug-ins, other than a Trim, and are sent to a ‘Hook Background’ aux, just below them, which itself also is sent to the ‘Hoof Ref’ track. It’s a pretty complicated vocal signal chain, as Schaeffer admits. > “The ‘Dot VS LD’ aux indeed has a lot of stuff on it! I did most of the processing on that bus. On the inserts there are the SSL E-Channel, Waves RComp, Waves Q10 EQ, Waves DeEsser, UAD LA2A, UAD Pultec EQP1A, SoundToys Decapitator and Pro?Q2. The SSL channel strip, Q10 and RCompressor remain from the tracking, and maybe the DeEsser as well, but I most likely messed with the settings more during mixing. The Q10 has a high-pass at 50Hz and I notched out a frequency that was bothering me around 8.5kHz with the Q2. I added the other plug-ins during mixing, and they all add something a bit different. I’m boosting 100Hz and 16kHz with the EQP1A. As I said, I like using several EQs on one thing. > “The sends go to a ‘FlangeVerb’ track, on which I put the RVerb and the UAD MXR Flanger, then the ‘Huge Verb’ with the [Audio Ease] Altiverb and EQ3, ‘Hook Valhalla’ with the Vintage Verb, and the SoundToys EchoBoy, the ‘EMT250’ aux with the UAD EMT250, Valhalla Plate and MicroShift, and then finally a send to the ‘Dot VS Delay’ track, with the EchoBoy, set to quarter note, the Reel Tape Flanger and the RCompressor. The EchoBoy is the main delay you can hear in the verse. The EMT250 is not set to a reverb, but to a phaser effect, which gives a cool stereo effect. The Valhalla adds a bit of reverb here, though it’s set to -12, so it only gives a tiny bit of ambience, and the MicroShift makes the whole thing a little wider. It probably still sounded a bit dry, which is why I sent the track to the ‘Huge Verb’ aux with the Altiverb, again taking out low end with the EQ3. > “In the pre-hook, Kendrick wanted that robotic sound with tons of effects. The main robotic effect comes from the iZotope VocalSynth, which gives it a vocoder-like sound. There also are some instances of the Little AlterBoy on the lead vocals in the pre-hook, with some formant adjusting and pitch-shifting. I think one of them is set to +12, so that’s an octave up, and another has a lower formant so it sounds pitched down, even though it remains in the same key. All that adds up to make the vocals sound robotic.” > Adding all inserts on audio and aux tracks together, Lamar’s verse rap is treated with a whopping 22 plug-ins! The ‘Hook Background’ aux, meanwhile, has the EQ3 seven-band, RCompressor, SoundToys Panman, a chorus, the MicroShift, the UAD MXR Flanger and the Valhalla Plate on the inserts and has sends to an aux track with the Waves Kramer Tape plug-in as well as the aforementioned ‘Hook Valhalla’ aux with the Vintage Verb, and Echoboy, and it then is routed to the ‘Hook Ref’ track, which has another four inserts and five sends. Phew.

Used by producer John Cuniberti on *Professor Satchafunkilus and the Musterion of Rock*: "Satriani and crew spent three weeks mixing at The Plant, where Cuniberti bypassed the SSL altogether to mix exclusively 'in the box.' After three weeks, they moved to his home studio, affectionately dubbed Digital Therapy Labs, which offers a Pro Tools HD3 system and enough plug-ins to allow him to use the same techniques as he would during a traditional mix session. 'I haven't changed the way I mix,' he says. 'I use the Waves API bundle for most of the EQ, the Altiverb reverbs — with those I can get my EMT plates, my echo chambers, my halls — and various compressors depending on what's called for. All of that is bused to a Neve 8-in/2-out summing box I built and then to an SSL stereo compressor. Joe and I have grown up with Neve, API and SSL consoles, so we couldn't divorce ourselves from them.'"

I don't use Reflektor, but I do use Altiverb, which is another kind of Impulse Response reverb. Everything in general has a lot of reverb, especially the leads.

"Here's the FX page... Over 120 unique reverbs, delays, compression, and eq for 48 separate quad outputs! #iFilmscoring"

Audio Ease Altiverb is included in the "Software Effects" list.

Mentioned by sound engineer Trevor Muzzy in this *Sound on Sound* interview about the production of "Starships". > "You can see that the pre-chorus and chorus vocals have a lot of timing and comp edits. They were imported directly from the session I cut the vocals in. I did not merge or consolidate them, they just are the way they are. There's quite a lot going on with the vocals. I tried to create a nice basic vocal sound using the inserts, and once they sat well in the track, most of the sonic variations between the sections came from the sends. There was no tuning on the rapping, but the sung vocals in this track had a fair amount of tuning with the Logic Pitch Corrector plug-in on the inserts. The tuning is part of the sound of the record, with vocals needing to be very, very precise. In some cases, we pitched them up or down for vocal effects. Logic Pitch Corrector is a little harder-sounding than Auto-Tune, but it has its own distinct sound that we liked for the vocals in this track. It really fits the song. > > "The other inserts on most of the vocals were all Waves: the C1 compressor, SSL Channel, Renaissance Channel, De-Esser, Renaissance Compressor, API 2500, and the Logic Channel EQ. The C1 compressor is the first in line on several lead vocals, and it does the same Pensado trick I used on the guitars, which is to compress a specific band — in the case of the verse lead vocal, around 2849Hz — focusing on notes that sounded a little harsh. It smooths this problem out more elegantly than using an EQ. Then the signal goes through the R Channel with some basic EQ, cutting significantly at 281Hz. Again, it was a matter of removing some less pleasant things to let the nice aspects shine. I bypassed the compressor in the R Channel. I needed a bit of de-essing, and the Waves De-Esser is a great all-purpose de-esser, in this case working at 5634Hz with the side-chain set to high-pass. > > "There were two more compressors on her vocal. There was no science behind this, it was just a matter of experimenting to find a unique sound. The first is the Renaissance Compressor, which I love and which is set to a fast attack time and takes off about 6dB, so quite subtle, not too intense. The API 2500 is set pretty aggressively and you can hear it pumping a little bit on the vocal. It was already in the session — it had been used on the demo vocal. I pulled it over to Nicki's channel and liked what it was doing, so I adjusted it to fit her vocal. Finally, the Channel EQ notches quite a lot around 600Hz and a little bit more around 235Hz, just carving out some low-mids to make the vocal sit better in the track. > > "Regarding the sends, there are some really distinct things happening here. The main lead vocal was similar throughout the song, but I tweaked it as it went along. The pre-chorus and chorus vocals all have Bus 1, which went to the same Altiverb effect that I had on the drums, to add some ambience to the vocal. The rap verses are much drier. Bus 35 is the Waves Doubler, which gives a bit of spread to the lead vocal — I used this on the rap as well as on the sung vocals. Bus 4 is the Waves CLA with a drastic telephone effect. That was another effect that was there from the demo version and added a cool quality. Bus 50 is the [Sound Toys] Echo Boy, which is the main plug-in I use for delay throws, whenever I want to repeat a word. In this case it's on a quarter-note Echoplex setting. It's a single, mono echo that I panned a little bit to the side. Bus 7 has the Waves VX1 Maserati Vocal Enhancer, and that was, again, a plug-in I inherited. It is set to a very compressed, bright vocal sound that I brought in and out to add some sparkle to the sound when necessary. > > "Bus 6 has the main reverb in the track, which you are hearing in the pre-chorus and chorus, and which is a Lexicon Plate plug-in on the 'VocalPlate2' preset. It's a really bright, over-the-top plate sound that is not trying to blend in but that's actually brightening the vocal up a lot. It's loud and wet. Busses 16 and 29 are different stereo delays: the Waves SuperTap was already in the session and I kept it, and the other is a standard Logic stereo delay that I use all the time on vocals. Bus 3 is the Logic Bitcrusher, which gives the vocals a grainy sound. The vocals already had an aggressive sonic quality to them because of the 251-TG2-1176 chain, and the Bitcrusher enhanced that. It's nasty, there's nothing nice about a bit-crusher, and it adds a bit of attitude. I used it on some of the background vocals as well, like in the second verse, where you have the pitch effects. You can hear it in the very processed harmony vocals that come in. That was something we added when we were doing the final vocal comp and arrangement. It gave that second verse some more life and helped the track build. The background vocals are a very big part of the hook vocal sound as well, and, for example, track 140 has many effects on it. That actually contains the vocals of the demo singers. Nicki's lead and background vocals are dominant, but in the chorus the background vocals from Mohombi and Wayne Hector added to the crowd feeling. The chorus vocals are really big in this track, and they were part of that.”

According to Sound On Sound article, Andrews used this plugin for Paramore record(s).

Used on Lovato's vocals for Clean Bandit's "Solo", as mentioned by mix engineer Mark Ralph in this November 2018 *Sound on Sound* interview. > There also are very few sends in the session, and only Demi Lovato’s lead vocal tracks have sends to the three aux effect tracks: reverbs from Audio Ease’s Altiverb and Valhalla DSP’s Valhalla Room, plus delay from SoundToys’ Echoboy.

Used on "Apeshit", as stated by producer Stuart White in this September 2018 *Sound on Sound* interview. > The first four aux tracks feature SoundToys effects, namely Little Microshift, two EchoBoy delays, and a delay from the Little PrimalTap. Next are a Hall Reverb aux and a Church Reverb aux, both using Waves’ RVerb, an EMT plate from Audio Ease’s Altiverb, four aux tracks with the Waves H-Delay and various other plug-ins on them as well, and four more reverb auxes with the Avid Revibe II, two Avid D-Verbs and another RVerb. > White: “I use the Little Microshift in pretty much every mix, with the left-right micro pitch-shift effect that’s similar to the classic effect in the Eventide H3000 shift where you pitch one side down six cents and one side up six cents to create width. It’s a good way to get your vocals wider without them being out of phase. It thickens up vocals, and is kind of like a doubler. I do quite a lot of filtering on some of the EchoBoy delays, for example with the Waves REQ, and I am adding colour with the SoundToys Devil-Loc, which is great if you want to colour the delay so it is separate from the main vocal, and compress it with the UAD LA3A and mix that in to taste.” > (...) Beyoncé’s lead vocal tracks consist of three aux tracks, four ‘dirty’ and eight ‘clean’ audio tracks. The audio tracks only have the EQ3 on the inserts and a few of them have a send to the Church Reverb. All White’s processing is done on the three aux tracks. “All lead vocals are sent to the ‘B Aux’ track and the ‘B Parra Aux’ tracks. On the former I have the McDSP DS 555 de-esser. I use the Waves de-esser the most, but in this particular track, because I wanted to compress her voice really hard, I felt that the 555 would work the best. I am rolling off until 6144Hz into what it is detecting; it’s like a side-chain filter. The FabFilter Pro-DS is doing a little more gentle look-ahead de-essing. > “After that there’s some pretty heavy EQ from the EQ3, with a high-pass at 142Hz, a 9dB cut at 244Hz and a 2dB cut at 3kHz. My cut at 244Hz is because she is singing in this husky, low voice, so there’s not a lot of energy in that. I get the energy from the RComp compression, and the EQs, including from the SSL E-Channel, are there to make her sit in the track, rather than making it sound filtered. I love the RComp, mainly because it doesn’t sound like compression to me. The SSL E-Channel adds a bit more compression, and the [Crane Song] Phoenix II Tape Emulation is really cool because while it doesn’t actually sound like tape, it smoothes out transients in a signal just like much analogue equipment does. It enables me to get a fatter vocal sound that again makes the vocal sit in the mix. The final EQ3 has a notch at 3.2kHz to take out some harshness. I also have sends to the Verb aux track, which are the D-Verb and [Waves] H-Reverb, and the Delay 1-4 aux, with the EchoBoy. > The other aux track, ‘B Parra Aux’, is a parallel compression track, with the RCompressor and the CLA 76, which I mixed in low. Both these aux tracks then go to the ‘LD ALL Aux’, on which I’m doing some more surgery with the McDSP AE400 [dynamic EQ], which allows you to set a threshold, just like on a compressor. It’s like turning a volume knob down on a frequency the moment it gets out of control. Finally, there’s the Waves C4, for some control, to keep the vocal even. This track has a lot of energy, so this is an example of using compression for energy, mood and attitude. I also worked a long time to get the compression on Bey’s breaths to pump on the beat. I wanted her breaths to be another percussive element in the track, and getting the attack and release on the compressor right was key to getting that feel and pumping effect.” > Five of the 22 Beyoncé ad lib, backing and harmony vocals below her lead vocals also go to the above-mentioned aux tracks, while the rest have their own signal chains. These audio tracks are sent to several aux tracks, often with tons of plug-ins, and all aux vocal tracks in the end get sent to the ‘Voc All’ group aux right at the top of the session, which has an RCompressor, with ratio at 10:1. There are more group aux tracks, like ‘TrackAux’, ‘FX Voc Aux’, ‘FX’ and ‘Music Aux’, which all get sent to the ‘All Aux’. This in turn gets sent to the ‘no limiter’ mix print track, and finally there’s a Stereo Master track.

Used on vocals and piano for the *Take Me to Church* EP, as stated by mix engineer Rob Kirwan in this March 2015 *Sound on Sound* interview. > “And finally, a lot of people, including artists, have been asking me for the nature of the reverb on Andrew’s vocals. It’s a combination of my Knas Moisturizer that I already mentioned, and the Altiverb [plug–in]. I used a Wendy Carlos EMT plate [preset], from which I removed all the top end, and to which I added a pre–delay.” > (...) * **Guitars & keyboards:** TL Labs TL Aggro, Avid Trim, Waves Puigtech EQP1A, Eventide H3000, Focusrite Red EQ & Audio Ease Altiverb. > “Below the ‘Kit Plate’ aux track are four organ tracks. The top two were recorded through an amplifier via my 57 and Delta mics, and below that is a distorted organ track, with the Trillium Lane Labs TL Aggro compression plug–in on it and a Pultec EQ. The ‘Organ 3000’ track is probably me putting one of Andrew’s Logic organs through my Eventide H3000. Further down are six guitar tracks without any treatments — the ‘T’ on one of them is a Trim — and below that are the piano tracks, some of which are again heavily edited. Andrew wasn’t as good yet at playing the piano. He’s very good now, though! I got him to do the left hand separately, which are the ‘New Piano’ tracks. I once again had the Focusrite Red EQ plug–in on the piano, and there’s a ‘Piano Verb’ aux track, which also has the Wendy Carlos EMT plate from Altiverb, just with a different pre–delay. In general I like to create a sense of everything coming from the same space, so the Wendy Carlos plate is on many things in this song. There’s more piano below that, again with just Focusrite EQ. In all there’s a lot of piano, it was one of the most important elements of the song.” > * **Vocals:** Bomb Factory 1176, Focusrite Red EQ, SoundToys Echo Boy, Line 6 Echo Farm, Knas Ekdahl Moisturizer, Waves Renaissance Compressor, Avid Trim & Audio Ease Altiverb. > “The two ‘tele’ voices at the top are backing vocals. I think they were ‘oohs’ and ‘aahs’ that came from the demo. They don’t sound like telephone voices at all, so I’m not sure why they’re called that. Instead they almost sound like church voices. Below are two aux tracks for those vocals, with Bomb Factory compression, Focusrite EQ and an Echo Boy delay. The backing vocals below that — ‘BV1–4’ — are the ones with the signature Leslie effect on them, and they again have some Focusrite EQ and Bomb Factory compression, and I gave them some Echo Farm slap delay to add depth to the reverb. > “The next tracks are the verse lead vocals from his Logic session, called ‘Male Creamy Lead Vocals’, on which I put some Renaissance compression and a Trim, and ‘Vox Verb’ is the Moisturizer track, plus two Trim plug–ins, one being +1dB and the other –0.5dB. I hate automating in Pro Tools, so I will often use the Trim to bypass it. Writing automation is a tedious task. Below this are the chorus vocals, called ‘New Vocal’, so we obviously recorded these again at my studio. In order to make them sound like the demo vocal I stuck them through the same chain and EQ’d them heavily. ‘Vox Plate’ is the Altiverb, and there’s a delay track below it which again has the Echo Farm, on a delay setting. Finally there are several more double–tracked chorus vocals, and they also have the Renaissance and Focusrite, and the Moisturizer and Echo Farm aux tracks below them.”

Plugin that creates reverb effects

Used for Quavo and Offest's features on Beyoncé and Jay-Z's "Apeshit", as stated by producer Stuart White in this September 2018 *Sound on Sound* interview. > The first four aux tracks feature SoundToys effects, namely Little Microshift, two EchoBoy delays, and a delay from the Little PrimalTap. Next are a Hall Reverb aux and a Church Reverb aux, both using Waves’ RVerb, an EMT plate from Audio Ease’s Altiverb, four aux tracks with the Waves H-Delay and various other plug-ins on them as well, and four more reverb auxes with the Avid Revibe II, two Avid D-Verbs and another RVerb. > White: “I use the Little Microshift in pretty much every mix, with the left-right micro pitch-shift effect that’s similar to the classic effect in the Eventide H3000 shift where you pitch one side down six cents and one side up six cents to create width. It’s a good way to get your vocals wider without them being out of phase. It thickens up vocals, and is kind of like a doubler. I do quite a lot of filtering on some of the EchoBoy delays, for example with the Waves REQ, and I am adding colour with the SoundToys Devil-Loc, which is great if you want to colour the delay so it is separate from the main vocal, and compress it with the UAD LA3A and mix that in to taste.” > (...) “The Migos vocals came in as seven audio tracks, with the Avid D-Verb on each of them. Putting a D-Verb on a track before EQ is not something I normally do, but it sounded great. So I adjusted them a bit, but otherwise left them as they were. The tracks also came in with the Aux track above, and the EQ3, with a high pass at 60Hz and notches at 430Hz and 1.41kHz and a high boost, the Waves API 2500 compressor, the RComp, the Waves Q10 EQ, following a slightly similar curve to the EQ3, the Waves De-esser, the Waves Aphex Aural Exciter, and the Avid Dyn3 expander/gate. I added the EQ3, with another high-pass filter at 144Hz, and the RComp, with a ratio of 10:1.”

Used for Quavo and Offest's features on Beyoncé and Jay-Z's "Apeshit", as stated by producer Stuart White in this September 2018 *Sound on Sound* interview. > The first four aux tracks feature SoundToys effects, namely Little Microshift, two EchoBoy delays, and a delay from the Little PrimalTap. Next are a Hall Reverb aux and a Church Reverb aux, both using Waves’ RVerb, an EMT plate from Audio Ease’s Altiverb, four aux tracks with the Waves H-Delay and various other plug-ins on them as well, and four more reverb auxes with the Avid Revibe II, two Avid D-Verbs and another RVerb. > White: “I use the Little Microshift in pretty much every mix, with the left-right micro pitch-shift effect that’s similar to the classic effect in the Eventide H3000 shift where you pitch one side down six cents and one side up six cents to create width. It’s a good way to get your vocals wider without them being out of phase. It thickens up vocals, and is kind of like a doubler. I do quite a lot of filtering on some of the EchoBoy delays, for example with the Waves REQ, and I am adding colour with the SoundToys Devil-Loc, which is great if you want to colour the delay so it is separate from the main vocal, and compress it with the UAD LA3A and mix that in to taste.” > (...) “The Migos vocals came in as seven audio tracks, with the Avid D-Verb on each of them. Putting a D-Verb on a track before EQ is not something I normally do, but it sounded great. So I adjusted them a bit, but otherwise left them as they were. The tracks also came in with the Aux track above, and the EQ3, with a high pass at 60Hz and notches at 430Hz and 1.41kHz and a high boost, the Waves API 2500 compressor, the RComp, the Waves Q10 EQ, following a slightly similar curve to the EQ3, the Waves De-esser, the Waves Aphex Aural Exciter, and the Avid Dyn3 expander/gate. I added the EQ3, with another high-pass filter at 144Hz, and the RComp, with a ratio of 10:1.”

> One of the last things that we recorded on the album was a guitar outro that I wrote and played for “Don’t Lie.” We just plugged a Les Paul guitar into the DI of the Apollo. I got really used to using a combination of Avid SansAmp and the ATR-102 Mastering Tape Recorder Plug-in — just those two with some AltiVerb Reverb. That gave us a scrappy sound that I’m very fond of.

"One of my go-to bits of gear when mixing is the Altiverb EMT 140 Wendy Carlos plate reverb. It's by no means the only verb I use, but if I'm not trying to sit the various elements in a room that others are sat in, then this is pretty much what I get up first. I'll often use the pre-delay that comes with the plugin, or put my own delay in front of it. If I want something with a little more movement, I'll chuck a tape delay before the Altiverb. It's a really lovely reverb. We’ve also used Altiverb to make an impulse response of the big room at Blueprint, which has come in handy now and again as we have used that room quite a bit over the years."

Used on Jones' vocals for *The Fall*, as stated by producer Jacquire King in this February 1, 2010 *Electronic Musician* interview with Jones, Jacquire King and assistant engineer Brad Bivens. > She was into adding delay on her voice, trying not to just make it pretty with reverb. The delays were both analog and plug-in. I use Audio Ease Altiverb, SoundToys EchoBoy delay, some of the UA plug-ins—they have a nice EMT 140 emulation—and the Cooper Time Cube Delay. We used The Magic Shop’s Marshall Tape Eliminator AR-300, a tape slap simulator. And Norah had an old Ibanez analog delay. We used a Roland Chorus Echo and EMT 140 plate reverbs, too. Sometimes I will use an Eventide H3000 for harmonic delay effects, and as I get them going I will print them in Pro Tools with the transfer from analog.

Take a look at the list at the bottom of the article.

Plugin can be seen at 0:14

Mentioned at 1:18:09.

Used on "APESHIT", as stated by producer Stuart White in this September 2018 *Sound on Sound* interview. > The first four aux tracks feature SoundToys effects, namely Little Microshift, two EchoBoy delays, and a delay from the Little PrimalTap. Next are a Hall Reverb aux and a Church Reverb aux, both using Waves’ RVerb, an EMT plate from Audio Ease’s Altiverb, four aux tracks with the Waves H-Delay and various other plug-ins on them as well, and four more reverb auxes with the Avid Revibe II, two Avid D-Verbs and another RVerb. > White: “I use the Little Microshift in pretty much every mix, with the left-right micro pitch-shift effect that’s similar to the classic effect in the Eventide H3000 shift where you pitch one side down six cents and one side up six cents to create width. It’s a good way to get your vocals wider without them being out of phase. It thickens up vocals, and is kind of like a doubler. I do quite a lot of filtering on some of the EchoBoy delays, for example with the Waves REQ, and I am adding colour with the SoundToys Devil-Loc, which is great if you want to colour the delay so it is separate from the main vocal, and compress it with the UAD LA3A and mix that in to taste.” > (...) Jay-Z’s part consists of just two tracks, one lead, and one ad-lib, with an additional ‘reverse’ track, and a ‘jay clean’ track. White: “The main lead vocal track has the SSL E0-channel, Waves C4 multiband compressor for some control, FabFilter Pro-Q2 EQ, with a few notches, and McDSP AE400. Where Jay raps ‘Tell the Grammy’s fuck that 0 for 8 shit / have you ever seen a crowd goin’ apeshit?’, you can hear some stuff in the background, which is another example of me adding flair and energy. That actually comes from the third ‘Voice Sample’ track further up the session, on which I have some automated plug-ins, the ReVibe, Waves S1 Imager, and filter sweep from the EQ3. It’s subtle, but it gives you a little ear candy.”

In this list of Lustmord's software, he has Logic Pro X, Addictive Drums, Alitverb, XILS3, and ReCycle.

Listed under software; "Audioease Altiverb and Speakerphone"

I don't have anything that allows you to actually place the sound. I still use a lot of Audio Ease Altiverb, which has hundreds of impulse responses of actual spaces.

"I also use Altiverb a lot, which is a game changer."

This item is mentioned at 36:24 in the video.

In this interview,at 56:10,he confirms using the plugin for reverb.

Altiverb for reverb (seriously insanely good sounding reverb)

Used on Bocelli's vocals for *Cinema*, as mentioned by sound engineer Justin Cortelyou in this February 2019 *Sound on Sound* interview. > At the bottom are three aux effect tracks, with Valhalla Plate, Audio Ease Altiverb (on the Haydn Hall preset), and UAD EMT 140 reverbs. Notable in the session is that by far the most plug-ins are used on the two vocal tracks. (...) "All three aux reverbs were used on Andrea's main vocal track, as well as on Matteo's vocal tracks, because the reverbs each have different characteristics and it was all about getting the right blend. The Haydn Hall makes it sound a bit more like in the big hall at AIR, and the Valhalla Plate is a little brighter and not as dense. The EMT adds some warmth. We always played around with these three to get the right combination of colours. I had this vocal chain on Andrea's vocal in every song on the album, though there will have been slight differences in settings."

24:44 - When discussing a vocal mix, Kove pulls up this plugin and says "I've got this which is one of my favourite plugins, this is altiverb and it's a convolation reverb rather then a alrhythmical whatever. It's got a whole host of classic reverbs and it's got absolutly loads on hear and it's got fantastic springs, old school digital reverbs, plate reverbs and really good stuff. It's very CPU heavy but if you're looking to get that older school sound and classic sound this is fantastic"

Used on Bocelli's vocals for "Fall On You", as mentioned by sound engineer Justin Cortelyou in this February 2019 *Sound on Sound* interview. > At the bottom are three aux effect tracks, with Valhalla Plate, Audio Ease Altiverb (on the Haydn Hall preset), and UAD EMT 140 reverbs. Notable in the session is that by far the most plug-ins are used on the two vocal tracks. (...) "All three aux reverbs were used on Andrea's main vocal track, as well as on Matteo's vocal tracks, because the reverbs each have different characteristics and it was all about getting the right blend. The Haydn Hall makes it sound a bit more like in the big hall at AIR, and the Valhalla Plate is a little brighter and not as dense. The EMT adds some warmth. We always played around with these three to get the right combination of colours. I had this vocal chain on Andrea's vocal in every song on the album, though there will have been slight differences in settings."