sprucebringsteen's Activity

This ingenious device takes the timeless charm of delay and elevates it to a realm of sonic exploration that is nothing short of captivating. Repeats that are dark, grainy and definitely analogue in nature, with modulation that adds a wealth of options to further sculpt your tone. You can adjust the depth and speed of modulation, tweak the delay time, and blend the wet and dry signals giving endless options. This level of control empowers you to fine-tune your sound and explore a vast spectrum of sonic possibilities. Whether you're looking to add subtle depth or create mind-bending textures, the Movall Falling Star is your gateway to crafting sonic landscapes that captivate and inspire. Built for the Road: Crafted with top-quality components and housed in a rugged, road-ready enclosure, this pedal is built to withstand the rigors of touring and gigging. Power Requirement: 9V DC center negative (not include).

The most in-demand analog delay ever built. Musicians love it and collectors cherish it. Experience the analog edge. Nothing can compare to the organic sound of analog delay, and no one does analog like the Deluxe Memory Man! Up to 550 mS of vibrant echo that rivals tape delay; lush, spatial chorus and haunting vibrato are just a few of the treats in the Memory Man's sonic smorgasbord!

Studio-Grade Compressor with real Vacuum Tube Variable 1:1 - 1:∞ compression Ratio Capable of “Brick Wall” and “Soft Knee” compression Variable compression Attack and Release times Up to +30 dB of Gain for maximum headroom Heater In-rush current control warms tube upon power-up True Bypass Switching The RTC600 is like taking the finest studio-grade tube compressors and “squeezing” them all down into a single stompbox.

The RTC600 starts out with the same patented DBX compression circuit used in Maxon’s popular CP-9 Pro+ pedal - this circuit provides a very smooth, transparent, almost “glassy” compression with very low noise floor, even at maximum settings. Your guitar sounds like your guitar, only with compression added to smooth out the dynamics.

The RTC600’s dual-triode tube is positioned pre-compression, adding classic valve warmth to the signal without increasing noise levels.

With up to +30 dB of clean Gain, the RTC can be used as a clean booster or as an attenuator to clean up an already dirty amp.

The Addition of Attack and Release controls to the circuit allow for a wider variety of compression effects, including “Brick Wall” limiting and “Soft Knee” compression.

The RTC600 features an internal charge pump circuit that bumps the incoming voltage up to 25 volts, providing massive headroom and full-range frequency response. The RTC600 can be used with any instrument and for a variety of applications – it can be sent into an amp’s front end, placed in an effects loop, or used as an outboard processor for home recordings.

The RTC600 features True Mechanical Bypass switching using a 3PDT switch. The RTC600 comes complete with the Maxon AC2009 9-Volt power supply, an auto sensing digital power supply that can be used anywhere in the world.

For studio-quality compression in a compact Stompbox, the RTC600 is the only REAL choice.

Rack tube compressors of this quality can cost thousands of dollars more than the RTC600.

TECH TALK: The RTC600 features a completely new and improved circuit from its predecessor, the RCP660.

5 controls adjust the compression effect –

Threshold: Variable, 0dB to -40dB Output gain: Variable, 0dB to 30dB Compression Ratio: 1:1 to 1:Infinity Attack time (for 20dB gain increase): Variable, 20mSec to 600mSec Release time (for 20dB gain decrease): Variable, 140mSec to 700msec

A Gain reduction LED lights when the reduction is 4dB or more.

The RTC features an In-Rush Current Control system - As soon as power is applied to the pedal, a small current is applied to the tube and begins heating it at a very low voltage (much like a tube amp standby switch). This system dramatically extends the tube life. Once the pedal is engaged, 12.6 VDC is applied to the tube heater.

The RTC600 features mechanical true bypass switching via a Fujisoku 4PDT switch.

NOTE ON POWERING THE RTC600 - this pedal’s voltage regulator IC requires a high inrush current of approximately 2000 mA upon startup. When using with a Power Brick such as the Voodoo Labs Pedal Power 2+, this pedal should be connected to a high current power jack when possible.

Input Impedance: 500K Ohms

Output Impedance: 10K Ohms

Output Jack: 1/4 inch standard phone jack

Max Output Level: +20dBu (at 1 kHz)

Residual Noise: -94dBu or less (Input shorted, IHF-A weighted)

T.H.D. +N: 0.02% or less (at 1 kHz, -10dBu output)

Controls: THRESHOLD 0dBu to -40dBu RATIO 1:1 to infinity: 1 GAIN 0dB to +30dB ATTACK (for 20dB gain decrease) 20mSec to 600mSec RELEASE (for 20dB gain increase) 140mSec to 700mSecSwitch: BYPASS/EFFECT (Mechanical True Bypass using 3PDT switch)I/O: INPUT JACK, OUTPUT JACK, DC INPUT JACK

Indicator: BYPASS/EFFECT LED REDUCTION LED (When REDUCTION LED lights, compression is more than 4dB.)

Internal Circuit Voltage: 25 VDC (±12.5V) (DC to DC Converter)

Power Consumption: 240mA/9VDC

Dimensions: 121 (W) × 152(D) × 60 (H) mm / 4.8” (W) x 6” (D) x 2.4” (H)

Weight: Approx. 580g / 1.3 Lbs. (without AC adaptor)

Power Supply: AC adaptor AC2009

Accessory: AC adaptor AC2009* 0dBu=0.775Vrm * All specifications are subject to change for improvement without notice or obligation.All brand names and product names are trademarks or registered trademarks of their respective companies.

While the name and purpose of the new pedal is the same as the original '90s models, this version of Tube King, the TK999HT, differs from its two predecessors in that it features internal high voltage DC circuitry instead of previous starved plate low voltage circuitry. Includes AC adapter.

Using the 'starved plate' circuitry, the tube in the original Tube Kings really acted more as a filter to achieve tube tones. With the TK999HT the 12AX7 gets normal DC high voltage, allowing total linear operation of the tube. It works just like a tube preamp because it effectively is one. The result is that the TK999HT makes any solid-state amp sound just like a tube amp. The distortion is massive yet tight.

Features: - Genuine high voltage tube distortion pedal. - Actual 12AX7 tube for massive yet tight distortion. - 3-band active eq plus Presence switch for exacting tonal control. - Void control for sharp rhythmic dynamics. - Rigid zinc die-cast case. - 12v AC adapter included.

Controls: - Drive - Level - 3-band active EQ - Void adjustable noise gate: produces "Machine Gun" effects.

Tube King is the regal name in distortion pedals. The TK999OD Tube King Overdrive pedal features internal high voltage DC power - the best for making any solid-state amp sound just like a tube amp. The TK999OD Overdrive will give you anything from light break-up to super smooth hi-gain saturation. Features 3 Band EQ that allows you plenty of play in shaping the tone you're looking for. Includes a 12AX7 tube for true tube distortion!

Features: - Genuine tube design - Operates at 100V - 3 Band EQ with presence - Level control - Gain control - Hi/Low input switch - Power supply included

The Tube King TK999OD is a genuine high-voltage tube overdrive pedal that will give you anything from light break-up to super smooth hi-gain saturation and includes actual tube.

Using a 12AX7 tube, and powered from an external 15VAC supply, this pedal runs the tube in starved plate mode, for a real tube sound. Many pedals on the market have the word “tube” in their name, and while these can be quite good, they don’t use a real tube to get “that sound”. This is the Mozztronics take on a pedal with an actual 12AX7 tube inside. Some products with tubes use the tube for filtering only, in the “tone control” section of the circuit. What a waste of a tube. Mozztronics use the tube where it is meant to be used, in the gain stages, so the drive you hear is tube drive. As used by - Tim Rogers, Davey Lane, Bob Spencer, Rhys Bowkett (Trafalgars), Jamie Payet.