Larry Mullen, Jr.

According to this transcription of a February 1982 issue of U2 Magazine, "Larry has a somewhat unusual drum set up. Not that the kit itself was unusual, but it was arranged in an unusual manner and had several unusual extras. The basic kit is a very impressive all black Tama Fiberstar - all single headed, and including a 24" kick drum, 16" and 18" floor toms, and a selection of rather deep rack toms. The snare was a Ludwig 14"x61 " steel shell and he also has a pair of Latin Percussion Timbale. The cymbals comprised Zildjian 18" thin ride; 18" thin crash; 18" medium crash; 18" pang and 21" ride, with Paiste 14" hi-hats on a Premier Trilock pedal. The rest of the stands are Tama. The kit is miked using Sennheiser 421's for the kick and the floor toms, Shure SM57's for rack toms and snare, Electro-voice RE10 on the hi-hat and AKG D190's on the rest. No overhead mikes."

Used as overheads on the iNNOCENCE + eXPERIENCE tour.

“We have a fairly traditional mic setup for Larry [Mullen’s] drums, from Shure 421s on toms, to 57s on top and bottom snare, and Audio-Technica 4050s for overheads,” says monitor engineer CJ Eiriksson. “We keep the mics fairly close and tight on everything, which helps keep the arena bleed out of drums as much as possible.

Used for the snare on "Get On Your Boots", as stated by producer Declan Gaffney.

"Most of 'Get On Your Boots' was recorded in Dublin by Richard Rainey, and the basic backing tracks were done live, by the whole band together. There was an [Electro-Voice] RE20 inside the bass drum, with an SE Electronics Titan on the outside, a [Shure] 57 underneath the snare, and Richard had his own Heil mic on top, which he alternated with a Beyer M201; the toms were [Sennheiser] 421, overheads Coles 4038; ride cymbal was sometimes a 57, sometimes a [AKG] 451. Everything went through the Neve 1091 or 1093 mic pres."

Used for the rack toms and snare drum, as mentioned in this transcription of a February 1982 issue of U2 Magazine.

Larry has a somewhat unusual drum set up. Not that the kit itself was unusual, but it was arranged in an unusual manner and had several unusual extras. The basic kit is a very impressive all black Tama Fiberstar - all single headed, and including a 24" kick drum, 16" and 18" floor toms, and a selection of rather deep rack toms. The snare was a Ludwig 14"x61 " steel shell and he also has a pair of Latin Percussion Timbale. The cymbals comprised Zildjian 18" thin ride; 18" thin crash; 18" medium crash; 18" pang and 21" ride, with Paiste 14" hi-hats on a Premier Trilock pedal. The rest of the stands are Tama. The kit is miked using Sennheiser 421's for the kick and the floor toms, Shure SM57's for rack toms and snare, Electro-voice RE10 on the hi-hat and AKG D190's on the rest. No overhead mikes.

The SM57 was later used for the snare drum and ride cymbal on "Get On Your Boots", as stated by producer Declan Gaffney in this Sound on Sound interview.

"Most of 'Get On Your Boots' was recorded in Dublin by Richard Rainey, and the basic backing tracks were done live, by the whole band together. There was an [Electro-Voice] RE20 inside the bass drum, with an SE Electronics Titan on the outside, a [Shure] 57 underneath the snare, and Richard had his own Heil mic on top, which he alternated with a Beyer M201; the toms were [Sennheiser] 421, overheads Coles 4038; ride cymbal was sometimes a 57, sometimes a [AKG] 451. Everything went through the Neve 1091 or 1093 mic pres."

Used for the toms on "Get On Your Boots", as stated by producer Declan Gaffney.

"Most of 'Get On Your Boots' was recorded in Dublin by Richard Rainey, and the basic backing tracks were done live, by the whole band together. There was an [Electro-Voice] RE20 inside the bass drum, with an SE Electronics Titan on the outside, a [Shure] 57 underneath the snare, and Richard had his own Heil mic on top, which he alternated with a Beyer M201; the toms were [Sennheiser] 421, overheads Coles 4038; ride cymbal was sometimes a 57, sometimes a [AKG] 451. Everything went through the Neve 1091 or 1093 mic pres."

The 421 was later used for the same purpose on the iNNOCENCE + eXPERIENCE tour, as stated in this Mix Online article.

“We have a fairly traditional mic setup for Larry [Mullen’s] drums, from Shure 421s on toms, to 57s on top and bottom snare, and Audio-Technica 4050s for overheads,” says monitor engineer CJ Eiriksson. “We keep the mics fairly close and tight on everything, which helps keep the arena bleed out of drums as much as possible.

Used for the bass drum on Achtung Baby and Pop, as explained by engineer Robbie Adams in this July 1997 Sound on Sound interview.

DECONSTRUCTING DRUMS

Three years ago, U2 engineer Robbie Adams explained in SOS how he recorded Larry Mullen's drums with just three mics, an approach he had picked up from Flood, who, said Adams, "is bored with all this traditional, big stereo nonsense." Flood explained that his way of recording drums was partly born from necessity, and partly from reading Mark Lewisohn's classic book on The Beatles' recording sessions: "When we were working on Achtung Baby, we had two drum kits set up, and I had very few channels on the desk, so that was a bit of a problem. I noticed from the photographs in the Beatles book how there was always one mic parked just above the drum kit. I thought it was maybe just for the photo or something, but then I saw it in other studio shots as well, and so, because of the problem I had with too few channels, I decided to try it out on one of the two kits. I put one mic on the bass drum -- an AKG D12 or Neumann U47 -- a Shure SM57 on the snare, and an SM58 as the overhead just above the kit.

"What started to happen was that people would prefer that drum sound, even though it's virtually mono. I also noticed that with Larry, who is a powerful drummer, when you put the drums in stereo you have to have the levels up higher on playback, whereas the mono drums were more powerful, even at lower levels. When I thought about it, I realised that if you're standing in front of a drum kit, you hear it in mono -- you don't hear the toms panning neatly from left to right in your ears. Also, a mic just above the kit compresses the sound. And that's the same effect that happens in the ears of a drummer or when you stand close to the kit; the sound is compressing in your ears because of the level of air pressure. So when you have a cheap, lo-fi overhead mic in that position, and add compression on a mic that's already compressing, it brings out the excitement, the same feel and natural balance that the drummer is getting."

"I've used the three-mic approach as a starting point ever since. You can do all sorts of things with it. For example, if the room you're recording in is rather dead, you can add a bit of room reverb just on the mad-sounding compressed mic. That will give the illusion of the drums having space, and yet the physical punch still comes from the middle. I will sometimes add two more overheads, like a 414 or 87, placed a bit higher up, or at the same height as the drummer's ears. A lot of the times we end up monitoring kick, snare and these higher overheads, and then if the track sounds a bit lame, we'll feed that extra low overhead mic in, which can bring out all the reflections that the drummer gets and that you may not hear normally. It's always good to experiment and listen to the sound the drummer gets in the room. When we were working on Pop in Miami, we were in a room that had very little character, so we put the two ambient mics right in the corner, pointing towards the ceiling, away from the drum kit, thus deliberately creating a woolly, booming drum sound that went well with the brightness of the drum kit. We were always pushing for character, and trying to stay as far away as possible from a generic rock drum sound."

Used for the bass drum on Achtung Baby and Pop, as explained by engineer Robbie Adams in this July 1997 Sound on Sound interview.

DECONSTRUCTING DRUMS

Three years ago, U2 engineer Robbie Adams explained in SOS how he recorded Larry Mullen's drums with just three mics, an approach he had picked up from Flood, who, said Adams, "is bored with all this traditional, big stereo nonsense." Flood explained that his way of recording drums was partly born from necessity, and partly from reading Mark Lewisohn's classic book on The Beatles' recording sessions: "When we were working on Achtung Baby, we had two drum kits set up, and I had very few channels on the desk, so that was a bit of a problem. I noticed from the photographs in the Beatles book how there was always one mic parked just above the drum kit. I thought it was maybe just for the photo or something, but then I saw it in other studio shots as well, and so, because of the problem I had with too few channels, I decided to try it out on one of the two kits. I put one mic on the bass drum -- an AKG D12 or Neumann U47 -- a Shure SM57 on the snare, and an SM58 as the overhead just above the kit.

"What started to happen was that people would prefer that drum sound, even though it's virtually mono. I also noticed that with Larry, who is a powerful drummer, when you put the drums in stereo you have to have the levels up higher on playback, whereas the mono drums were more powerful, even at lower levels. When I thought about it, I realised that if you're standing in front of a drum kit, you hear it in mono -- you don't hear the toms panning neatly from left to right in your ears. Also, a mic just above the kit compresses the sound. And that's the same effect that happens in the ears of a drummer or when you stand close to the kit; the sound is compressing in your ears because of the level of air pressure. So when you have a cheap, lo-fi overhead mic in that position, and add compression on a mic that's already compressing, it brings out the excitement, the same feel and natural balance that the drummer is getting."

"I've used the three-mic approach as a starting point ever since. You can do all sorts of things with it. For example, if the room you're recording in is rather dead, you can add a bit of room reverb just on the mad-sounding compressed mic. That will give the illusion of the drums having space, and yet the physical punch still comes from the middle. I will sometimes add two more overheads, like a 414 or 87, placed a bit higher up, or at the same height as the drummer's ears. A lot of the times we end up monitoring kick, snare and these higher overheads, and then if the track sounds a bit lame, we'll feed that extra low overhead mic in, which can bring out all the reflections that the drummer gets and that you may not hear normally. It's always good to experiment and listen to the sound the drummer gets in the room. When we were working on Pop in Miami, we were in a room that had very little character, so we put the two ambient mics right in the corner, pointing towards the ceiling, away from the drum kit, thus deliberately creating a woolly, booming drum sound that went well with the brightness of the drum kit. We were always pushing for character, and trying to stay as far away as possible from a generic rock drum sound."

According to this transcription of a February 1982 issue of U2 Magazine, "Larry has a somewhat unusual drum set up. Not that the kit itself was unusual, but it was arranged in an unusual manner and had several unusual extras. The basic kit is a very impressive all black Tama Fiberstar - all single headed, and including a 24" kick drum, 16" and 18" floor toms, and a selection of rather deep rack toms. The snare was a Ludwig 14"x61 " steel shell and he also has a pair of Latin Percussion Timbale. The cymbals comprised Zildjian 18" thin ride; 18" thin crash; 18" medium crash; 18" pang and 21" ride, with Paiste 14" hi-hats on a Premier Trilock pedal. The rest of the stands are Tama. The kit is miked using Sennheiser 421's for the kick and the floor toms, Shure SM57's for rack toms and snare, Electro-voice RE10 on the hi-hat and AKG D190's on the rest. No overhead mikes."

According to the website U2 Atomic, Larry Mullen, Jr. used a Shure Beta 52 to mike his B-stage bass drum during U2's Joshua Tree tour.

Used for the bass drum on "Get On Your Boots", as stated by producer Declan Gaffney.

"Most of 'Get On Your Boots' was recorded in Dublin by Richard Rainey, and the basic backing tracks were done live, by the whole band together. There was an [Electro-Voice] RE20 inside the bass drum, with an SE Electronics Titan on the outside, a [Shure] 57 underneath the snare, and Richard had his own Heil mic on top, which he alternated with a Beyer M201; the toms were [Sennheiser] 421, overheads Coles 4038; ride cymbal was sometimes a 57, sometimes a [AKG] 451. Everything went through the Neve 1091 or 1093 mic pres."

Used for the bass drum on "Get On Your Boots", as stated by producer Declan Gaffney.

"Most of 'Get On Your Boots' was recorded in Dublin by Richard Rainey, and the basic backing tracks were done live, by the whole band together. There was an [Electro-Voice] RE20 inside the bass drum, with an SE Electronics Titan on the outside, a [Shure] 57 underneath the snare, and Richard had his own Heil mic on top, which he alternated with a Beyer M201; the toms were [Sennheiser] 421, overheads Coles 4038; ride cymbal was sometimes a 57, sometimes a [AKG] 451. Everything went through the Neve 1091 or 1093 mic pres."

Used as overheads on "Get On Your Boots", as stated by producer Declan Gaffney.

"Most of 'Get On Your Boots' was recorded in Dublin by Richard Rainey, and the basic backing tracks were done live, by the whole band together. There was an [Electro-Voice] RE20 inside the bass drum, with an SE Electronics Titan on the outside, a [Shure] 57 underneath the snare, and Richard had his own Heil mic on top, which he alternated with a Beyer M201; the toms were [Sennheiser] 421, overheads Coles 4038; ride cymbal was sometimes a 57, sometimes a [AKG] 451. Everything went through the Neve 1091 or 1093 mic pres."

Used for the ride cymbals on "Get On Your Boots", as stated by producer Declan Gaffney.

"Most of 'Get On Your Boots' was recorded in Dublin by Richard Rainey, and the basic backing tracks were done live, by the whole band together. There was an [Electro-Voice] RE20 inside the bass drum, with an SE Electronics Titan on the outside, a [Shure] 57 underneath the snare, and Richard had his own Heil mic on top, which he alternated with a Beyer M201; the toms were [Sennheiser] 421, overheads Coles 4038; ride cymbal was sometimes a 57, sometimes a [AKG] 451. Everything went through the Neve 1091 or 1093 mic pres."

Although the model is unspecified, mention of an EB in this article about the Joshua Tree Tour 2017 suggests it is that one.

Used for overheads on Pop, as explained by engineer Robbie Adams in this July 1997 Sound on Sound interview.

DECONSTRUCTING DRUMS

Three years ago, U2 engineer Robbie Adams explained in SOS how he recorded Larry Mullen's drums with just three mics, an approach he had picked up from Flood, who, said Adams, "is bored with all this traditional, big stereo nonsense." Flood explained that his way of recording drums was partly born from necessity, and partly from reading Mark Lewisohn's classic book on The Beatles' recording sessions: "When we were working on Achtung Baby, we had two drum kits set up, and I had very few channels on the desk, so that was a bit of a problem. I noticed from the photographs in the Beatles book how there was always one mic parked just above the drum kit. I thought it was maybe just for the photo or something, but then I saw it in other studio shots as well, and so, because of the problem I had with too few channels, I decided to try it out on one of the two kits. I put one mic on the bass drum -- an AKG D12 or Neumann U47 -- a Shure SM57 on the snare, and an SM58 as the overhead just above the kit.

"What started to happen was that people would prefer that drum sound, even though it's virtually mono. I also noticed that with Larry, who is a powerful drummer, when you put the drums in stereo you have to have the levels up higher on playback, whereas the mono drums were more powerful, even at lower levels. When I thought about it, I realised that if you're standing in front of a drum kit, you hear it in mono -- you don't hear the toms panning neatly from left to right in your ears. Also, a mic just above the kit compresses the sound. And that's the same effect that happens in the ears of a drummer or when you stand close to the kit; the sound is compressing in your ears because of the level of air pressure. So when you have a cheap, lo-fi overhead mic in that position, and add compression on a mic that's already compressing, it brings out the excitement, the same feel and natural balance that the drummer is getting."

"I've used the three-mic approach as a starting point ever since. You can do all sorts of things with it. For example, if the room you're recording in is rather dead, you can add a bit of room reverb just on the mad-sounding compressed mic. That will give the illusion of the drums having space, and yet the physical punch still comes from the middle. I will sometimes add two more overheads, like a 414 or 87, placed a bit higher up, or at the same height as the drummer's ears. A lot of the times we end up monitoring kick, snare and these higher overheads, and then if the track sounds a bit lame, we'll feed that extra low overhead mic in, which can bring out all the reflections that the drummer gets and that you may not hear normally. It's always good to experiment and listen to the sound the drummer gets in the room. When we were working on Pop in Miami, we were in a room that had very little character, so we put the two ambient mics right in the corner, pointing towards the ceiling, away from the drum kit, thus deliberately creating a woolly, booming drum sound that went well with the brightness of the drum kit. We were always pushing for character, and trying to stay as far away as possible from a generic rock drum sound."