Taylor Hawkins

In this video, at the 0:16 second mark you see Taylor Hawkins' drumset with a painted LP Rock Classic Ridge Rider Cowbell. It is also noted in an interview for Guitar Center (http://gc.guitarcenter.com/interview/taylor-hawkins/) that he uses an LP Cowbell: "Hawkins frequently mounts a Latin Percussion cowbell to the right of his first floor tom..."

Used on the Concrete and Gold tour, the "grain" of the concrete can be seen on careful inspection

at 1:46, he is playing this guitar

Used for the bass drum on "The Pretender", as stated by mix engineer Rich Costey in this March 2008 Sound on Sound interview.

Drums: Quad 8 310, Pultec EQP1, API 550a, Neve 33609, API 2500, Lexicon 960, Urei 1176, Smart C2, SPL Transient Designer, room mics

"I had just gotten some Quad 8 310 EQs before I began the Foo Fighters project, and I found that cranking the s[**]t out of the mid-range with the Quads helped the drums quite a lot. On most of the album the bass and snare drum went through the Quad 8s, with severe amounts of mid-range added. Quad 8 grew out of Electrodyne and was very popular in the 1970s, particularly with film companies. I obtained some channels that came out of the Motown Sunrise console and they're basically three bands of EQ and a mic pre and output level, and the Q gets tighter as you push it up. The Quad 8s are a little bit rounder and warmer-sounding than similar API modules. I also used the Pultec EQP1 and API 550a on the bass drum.

"I had a bunch of different side-chain compressors on the drums that would change from song to song. On some songs it would be the Smart C2, medium ratio and fast recovery, on others the Neve 33609, the Urei 1176, the API 2500 or the Empirical Labs Distressor, and the SPL Transient Designer on toms. You can use the SPL to lengthen the sound of the toms. I don't compress all the drums at the same time, I'll compress individual parts and mix the compressed sound in with the natural sound of the drums. There was relatively little compression implemented on the drums in this song, because the band didn't care for it. They wanted the drums to sound more raw.

"Throughout the album mix I might have used a bit of Lexicon 960 on the drums for reverb, but the room mics — amongst them a heavily compressed foldback microphone — were so good that I tended to use those. I tend to like room mics that are on the darker side. If they're too bright, you can't turn them up very loud because you then also get all kinds of messy cymbal noises. One other thing to note is the drums that come in after the intro of the song. When the whole band is slamming accents like that, you want to make the drums sound very aggressive, and this meant pushing room mics, pushing compression mics and so forth. As I said, there were a lot of rides."

In the BAE AUDIO YouTube video titled "Foo Fighters Taylor Hawkins Song Demo," Taylor Hawkins is seen with a Gibson DG-335 in the background.

According to Remo's Artist page, Taylor Hawkins uses Clear Ambassador drum heads.

This video shows Taylor Hawkins' Signature Series Snare Drum using the Remo Coated Emperor X.

In this video at the 1:07 mark, you can see Taylor Hawkins uses a Gold Plated Gibraltar 6710 Pro Double Braced Straight Cymbal Stand on The Foo Fighters touring kit.

In a YouTube video titled "Taylor Hawkins And Dave Grohl - Drum Solo," Taylor Hawkins can be seen using the DW 5000 Single Bass Drum Pedal during a performance at the Lost Highway festival.

In the Foo's recent bbc radio 1 live show, taylor wearing a set of Vic Firth isolation headphones.

Can be seen throughout the video for the china and crashes

at 1:16, he is playing this guitar

at 1:40, he is playing this guitar

at 1:20, this amp can be seen behind taylor

Used for the bass drum on "The Pretender", as stated by mix engineer Rich Costey in this March 2008 Sound on Sound interview. An image of the settings for bandmate Dave Grohl's intro vocals shows that it is the Bomb Factory plugin.

Drums: Quad 8 310, Pultec EQP1, API 550a, Neve 33609, API 2500, Lexicon 960, Urei 1176, Smart C2, SPL Transient Designer, room mics

"I had just gotten some Quad 8 310 EQs before I began the Foo Fighters project, and I found that cranking the s[**]t out of the mid-range with the Quads helped the drums quite a lot. On most of the album the bass and snare drum went through the Quad 8s, with severe amounts of mid-range added. Quad 8 grew out of Electrodyne and was very popular in the 1970s, particularly with film companies. I obtained some channels that came out of the Motown Sunrise console and they're basically three bands of EQ and a mic pre and output level, and the Q gets tighter as you push it up. The Quad 8s are a little bit rounder and warmer-sounding than similar API modules. I also used the Pultec EQP1 and API 550a on the bass drum.

"I had a bunch of different side-chain compressors on the drums that would change from song to song. On some songs it would be the Smart C2, medium ratio and fast recovery, on others the Neve 33609, the Urei 1176, the API 2500 or the Empirical Labs Distressor, and the SPL Transient Designer on toms. You can use the SPL to lengthen the sound of the toms. I don't compress all the drums at the same time, I'll compress individual parts and mix the compressed sound in with the natural sound of the drums. There was relatively little compression implemented on the drums in this song, because the band didn't care for it. They wanted the drums to sound more raw.

"Throughout the album mix I might have used a bit of Lexicon 960 on the drums for reverb, but the room mics — amongst them a heavily compressed foldback microphone — were so good that I tended to use those. I tend to like room mics that are on the darker side. If they're too bright, you can't turn them up very loud because you then also get all kinds of messy cymbal noises. One other thing to note is the drums that come in after the intro of the song. When the whole band is slamming accents like that, you want to make the drums sound very aggressive, and this meant pushing room mics, pushing compression mics and so forth. As I said, there were a lot of rides."

Used for the drums on Echoes, Silence, Patience & Grace, as stated by mix engineer Rich Costey in this March 2008 Sound on Sound interview.

Drums: Quad 8 310, Pultec EQP1, API 550a, Neve 33609, API 2500, Lexicon 960, Urei 1176, Smart C2, SPL Transient Designer, room mics

"I had just gotten some Quad 8 310 EQs before I began the Foo Fighters project, and I found that cranking the s[**]t out of the mid-range with the Quads helped the drums quite a lot. On most of the album the bass and snare drum went through the Quad 8s, with severe amounts of mid-range added. Quad 8 grew out of Electrodyne and was very popular in the 1970s, particularly with film companies. I obtained some channels that came out of the Motown Sunrise console and they're basically three bands of EQ and a mic pre and output level, and the Q gets tighter as you push it up. The Quad 8s are a little bit rounder and warmer-sounding than similar API modules. I also used the Pultec EQP1 and API 550a on the bass drum.

"I had a bunch of different side-chain compressors on the drums that would change from song to song. On some songs it would be the Smart C2, medium ratio and fast recovery, on others the Neve 33609, the Urei 1176, the API 2500 or the Empirical Labs Distressor, and the SPL Transient Designer on toms. You can use the SPL to lengthen the sound of the toms. I don't compress all the drums at the same time, I'll compress individual parts and mix the compressed sound in with the natural sound of the drums. There was relatively little compression implemented on the drums in this song, because the band didn't care for it. They wanted the drums to sound more raw.

"Throughout the album mix I might have used a bit of Lexicon 960 on the drums for reverb, but the room mics — amongst them a heavily compressed foldback microphone — were so good that I tended to use those. I tend to like room mics that are on the darker side. If they're too bright, you can't turn them up very loud because you then also get all kinds of messy cymbal noises. One other thing to note is the drums that come in after the intro of the song. When the whole band is slamming accents like that, you want to make the drums sound very aggressive, and this meant pushing room mics, pushing compression mics and so forth. As I said, there were a lot of rides."

Used for the drums on Echoes, Silence, Patience & Grace, as stated by mix engineer Rich Costey in this March 2008 Sound on Sound interview.

Drums: Quad 8 310, Pultec EQP1, API 550a, Neve 33609, API 2500, Lexicon 960, Urei 1176, Smart C2, SPL Transient Designer, room mics

"I had just gotten some Quad 8 310 EQs before I began the Foo Fighters project, and I found that cranking the s[**]t out of the mid-range with the Quads helped the drums quite a lot. On most of the album the bass and snare drum went through the Quad 8s, with severe amounts of mid-range added. Quad 8 grew out of Electrodyne and was very popular in the 1970s, particularly with film companies. I obtained some channels that came out of the Motown Sunrise console and they're basically three bands of EQ and a mic pre and output level, and the Q gets tighter as you push it up. The Quad 8s are a little bit rounder and warmer-sounding than similar API modules. I also used the Pultec EQP1 and API 550a on the bass drum.

"I had a bunch of different side-chain compressors on the drums that would change from song to song. On some songs it would be the Smart C2, medium ratio and fast recovery, on others the Neve 33609, the Urei 1176, the API 2500 or the Empirical Labs Distressor, and the SPL Transient Designer on toms. You can use the SPL to lengthen the sound of the toms. I don't compress all the drums at the same time, I'll compress individual parts and mix the compressed sound in with the natural sound of the drums. There was relatively little compression implemented on the drums in this song, because the band didn't care for it. They wanted the drums to sound more raw.

"Throughout the album mix I might have used a bit of Lexicon 960 on the drums for reverb, but the room mics — amongst them a heavily compressed foldback microphone — were so good that I tended to use those. I tend to like room mics that are on the darker side. If they're too bright, you can't turn them up very loud because you then also get all kinds of messy cymbal noises. One other thing to note is the drums that come in after the intro of the song. When the whole band is slamming accents like that, you want to make the drums sound very aggressive, and this meant pushing room mics, pushing compression mics and so forth. As I said, there were a lot of rides."

Used for the drums on Echoes, Silence, Patience & Grace, as stated by mix engineer Rich Costey in this March 2008 Sound on Sound interview.

Drums: Quad 8 310, Pultec EQP1, API 550a, Neve 33609, API 2500, Lexicon 960, Urei 1176, Smart C2, SPL Transient Designer, room mics

"I had just gotten some Quad 8 310 EQs before I began the Foo Fighters project, and I found that cranking the s[**]t out of the mid-range with the Quads helped the drums quite a lot. On most of the album the bass and snare drum went through the Quad 8s, with severe amounts of mid-range added. Quad 8 grew out of Electrodyne and was very popular in the 1970s, particularly with film companies. I obtained some channels that came out of the Motown Sunrise console and they're basically three bands of EQ and a mic pre and output level, and the Q gets tighter as you push it up. The Quad 8s are a little bit rounder and warmer-sounding than similar API modules. I also used the Pultec EQP1 and API 550a on the bass drum.

"I had a bunch of different side-chain compressors on the drums that would change from song to song. On some songs it would be the Smart C2, medium ratio and fast recovery, on others the Neve 33609, the Urei 1176, the API 2500 or the Empirical Labs Distressor, and the SPL Transient Designer on toms. You can use the SPL to lengthen the sound of the toms. I don't compress all the drums at the same time, I'll compress individual parts and mix the compressed sound in with the natural sound of the drums. There was relatively little compression implemented on the drums in this song, because the band didn't care for it. They wanted the drums to sound more raw.

"Throughout the album mix I might have used a bit of Lexicon 960 on the drums for reverb, but the room mics — amongst them a heavily compressed foldback microphone — were so good that I tended to use those. I tend to like room mics that are on the darker side. If they're too bright, you can't turn them up very loud because you then also get all kinds of messy cymbal noises. One other thing to note is the drums that come in after the intro of the song. When the whole band is slamming accents like that, you want to make the drums sound very aggressive, and this meant pushing room mics, pushing compression mics and so forth. As I said, there were a lot of rides."

In the YouTube video "Foo Fighters Taylor Hawkins Song Demo" by BAE AUDIO, Taylor Hawkins is seen with a Laney 4x12 AOR Cabinet in the background, suggesting its use during the demo.

In the BAE AUDIO YouTube video titled "Foo Fighters Taylor Hawkins Song Demo," Taylor Hawkins can be seen with a Fender Chris Shiflett Telecaster Deluxe in Shoreline Gold in the background.

Is used at 0:16 in this video.

In the Sotheby's video titled "Foo Fighters Drummer Taylor Hawkins on Collecting, Rock & Roll Style," a Fender Stratacoustic guitar is visible in the background, suggesting it is part of Taylor Hawkins' collection.

In a video by Sotheby's titled "Foo Fighters Drummer Taylor Hawkins on Collecting, Rock & Roll Style," Taylor Hawkins discusses his use of the Strymon blueSky Reverberator.

In a Sotheby's video, Taylor Hawkins discusses his collection and can be seen with a Marshall JCM 2000 Dual Super Lead guitar amplifier head.

In a video by Sotheby's, Taylor Hawkins discusses his collection, featuring a Marshall 4x12 Cab with JBL 12" speakers.

Taylor Hawkins uses Gibraltar Boom Stands that are gold plated, as seen at the 0:40 second mark of this video of his Gretsch drum kit.

Taylor Hawkins uses a Gibraltar Turning Point Ultra Adjust Snare Stand, as seen at 0:28 second mark in this video clip of his Gretsch kit.

According to Remo's Artist page, Taylor Hawkins Uses Powerstroke 3 Smooth White bass drum heads.

According to Remo's Artist page, Taylor Hawkins uses Clear Emperor drum heads.

Can be seen at 9:56 in the foot cam